Using TP Link TL-SG108E web UI configuration tool on Ubuntu 22.04

My research was based on this great post from 2014.

This switch has UI which can be accessed via windows application and has UI which can be accessed via browser. 

Just for entertaining purposes I decided to try Window app on my Ubuntu 22.04 Linux machine.

To do so I installed wine:

sudo apt install wine-development

Then I downloaded version v1.3.10, 2022-04-12 from TP Link web site and unpacked it:

wget https://static.tp-link.com/upload/software/2022/202204/20220412/Easy%20Smart%20Configuration%20Utility%20v1.3.10.0.zip

unzip "Easy Smart Configuration Utility v1.3.10.0.zip"

After that I was able to run installer:

wine Easy\ Smart\ Configuration\ Utility\ v1.3.10.0.exe

Installation was finished successfully and then all exe files were put to "~/.wine/drive_c/Program Files (x86)/TPLINK/EasySmartConfigurationUtility".

And I was able to run it from first attempt:

cd ~/.wine/drive_c/Program Files (x86)/TPLINK/EasySmartConfigurationUtility 

wine Easy\ Smart\ Configuration\ Utility.jar

Unfortunately, it did not find switch:

Then I used trick from article I referenced above. You need to replace 192.168.1.201 by local IP address in your network:

echo 1 > /proc/sys/net/ipv4/ip_forward

iptables -t nat -A PREROUTING -p udp -d 255.255.255.255 --dport 29809 -j DNAT --to 192.168.1.201:29809

After that it worked just fine:

Yay! For some reasons DHCP did not work well and IP address wasn't changed. In this case UI tool solves one of the most annoying issues: IP address discovery. 

I was able to change password to new one but everything else causes wine to crash:

0130:err:ole:com_get_class_object class {597d4fb0-47fd-4aff-89b9-c6cfae8cf08e} not registered

0130:err:ole:com_get_class_object no class object {597d4fb0-47fd-4aff-89b9-c6cfae8cf08e} could be created for context 0x1

0130:err:ole:com_get_class_object class {597d4fb0-47fd-4aff-89b9-c6cfae8cf08e} not registered

0130:err:ole:com_get_class_object no class object {597d4fb0-47fd-4aff-89b9-c6cfae8cf08e} could be created for context 0x1

#

# A fatal error has been detected by the Java Runtime Environment:

#

#  EXCEPTION_ACCESS_VIOLATION (0xc0000005) at pc=0x6d2efe4d, pid=244, tid=304

#

# JRE version: 7.0_15-b03

# Java VM: Java HotSpot(TM) Client VM (23.7-b01 mixed mode windows-x86 )

# Problematic frame:

# C  [glass.dll+0xfe4d]  _Java_com_sun_glass_events_KeyEvent__1getKeyCodeForChar@12+0x134d

#

# Failed to write core dump. Minidumps are not enabled by default on client versions of Windows

#

# An error report file with more information is saved as:

# C:\Program Files (x86)\TPLINK\EasySmartConfigurationUtility\hs_err_pid244.log

#

# If you would like to submit a bug report, please visit:

#   http://bugreport.sun.com/bugreport/crash.jsp

# The crash happened outside the Java Virtual Machine in native code.

# See problematic frame for where to report the bug.

#

0130:err:msvcrt:_invalid_parameter (null):0 (null): (null) 0 

After reading the Internet I found that this exe file is in fact Java JAR file and I've tried running it using OpenJDK:

sudo apt install default-jre

Sadly it failed miserably:

java -jar Easy\ Smart\ Configuration\ Utility.exe 

Error: JavaFX runtime components are missing, and are required to run this application

As final attempt I've tried using Java from Oracle directly.   You need to download it manually and then unpack it:

sudo tar -xf jre-8u381-linux-i586.tar.gz -C /opt

And run:

/opt/jre1.8.0_381/bin/java -jar Easy\ Smart\ Configuration\ Utility.exe 

Sadly it failed too:

Exception in thread "main" java.lang.reflect.InvocationTargetException

at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)

at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:62)

at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43)

at java.lang.reflect.Method.invoke(Method.java:498)

at sun.launcher.LauncherHelper$FXHelper.main(LauncherHelper.java:904)

Caused by: java.lang.UnsupportedOperationException: Internal Error

at com.sun.glass.ui.gtk.GtkApplication.lambda$new$5(GtkApplication.java:158)

at java.security.AccessController.doPrivileged(Native Method)

at com.sun.glass.ui.gtk.GtkApplication.<init>(GtkApplication.java:140)

at com.sun.glass.ui.gtk.GtkPlatformFactory.createApplication(GtkPlatformFactory.java:41)

at com.sun.glass.ui.Application.run(Application.java:147)

at com.sun.javafx.tk.quantum.QuantumToolkit.startup(QuantumToolkit.java:279)

at com.sun.javafx.application.PlatformImpl.startup(PlatformImpl.java:211)

at com.sun.javafx.application.LauncherImpl.startToolkit(LauncherImpl.java:675)

at com.sun.javafx.application.LauncherImpl.launchApplicationWithArgs(LauncherImpl.java:337)

at com.sun.javafx.application.LauncherImpl.launchApplication(LauncherImpl.java:328)

... 5 more

 You may try running older version of Oracle Java as bundled JRE is dated by 2013:

root@station:/home/pavel/.wine/drive_c/Program Files (x86)/TPLINK/EasySmartConfigurationUtility/jre# head COPYRIGHT 

Copyright � 1993, 2013, Oracle and/or its affiliates. 

All rights reserved.

This software and related documentation are provided under a

license agreement containing restrictions on use and

disclosure and are protected by intellectual property laws.

Except as expressly permitted in your license agreement or

allowed by law, you may not use, copy, reproduce, translate,

broadcast, modify, license, transmit, distribute, exhibit,

perform, publish, or display any part, in any form, or by

root@station:/home/pavel/.wine/drive_c/Program Files (x86)/TPLINK/EasySmartConfigurationUtility/jre# cat release 

JAVA_VERSION="1.7.0"

OS_NAME="Windows"

OS_VERSION="5.1"

OS_ARCH="i586"

SOURCE=" .:f37a75bd3959 corba:e5b996dabec6 deploy:3bb10c0238fe hotspot:5b55cef461b0 hotspot/src/closed:759fc4d1d429 hotspot/test/closed:2d8e36f71952 install:0154bd493323 jaxp:a55f67cfe182 jaxws:eaf9b2990670 jdk:87e45d30e24d jdk/make/closed:b83ea3e4144a jdk/src/closed:d8651f160809 jdk/test/closed:7e4b15d6c1bb langtools:c160d7d1616d pubs:06f851196d93 sponsors:2dbf246921cb"

 

With IP address in hands I was able to access web UI:

And finally I can use capability for which this switch was bought - port mirror:

 

 

Ubuntu 22.04 installation on VirtualBox using command line

We use VirtualBox for process of preparing VM images for our product. Sadly some things had to be done manually and we're heading towards full automation and it was an attempt to prepare VM for Ubuntu 22.04 installation from ISO using only command line interface.

NB! If you have IPv4 disabled on your machine you have to enable it as otherwise VM will not have connection and installer may fail. 

Set some variables shared by next steps:

export VM_NAME=Ubuntu2204_TEST_OVA

export VM_ROOT_FOLDER="/home/pavel/VirtualBoxVMs"

export VM_FOLDER="$VM_ROOT_FOLDER/$VM_NAME"

By default VirtualBox uses path with nasty space in it and that's why I changed it to custom one without spaces as I do not like spaces and bash agrees with me about it. 

Create VM and register it in VirtualBox:

VBoxManage createvm --name $VM_NAME  --register  --ostype=Ubuntu22_LTS_64 --basefolder=$VM_ROOT_FOLDER

If you plan to use another OS then you can get all list of all OS types using this command:

VBoxManage list ostypes

Then set some basic hardware options:

VBoxManage modifyvm $VM_NAME --ioapic on                     

VBoxManage modifyvm $VM_NAME --memory 16384  --vram 128       

VBoxManage modifyvm $VM_NAME --cpus 8

VBoxManage modifyvm $VM_NAME  --nic1 nat

Then create 150G disk for VM and attach it to it:

VBoxManage createhd --filename $VM_FOLDER/disk.vdi --size 150000 --format VDI

Add SATA controller: 

VBoxManage storagectl $VM_NAME  --name "SATA Controller" --add sata --controller IntelAhci

And attach our disk to it: 

VBoxManage storageattach $VM_NAME  --storagectl "SATA Controller" --port 0 --device 0 --type hdd --medium  $VM_FOLDER/disk.vdi

Then add IDE controller to mount ISO disk with installer: 

VBoxManage storagectl $VM_NAME  --name "IDE Controller" --add ide --controller PIIX4 

VBoxManage storageattach $VM_NAME --storagectl "IDE Controller" --port 1 --device 0 --type dvddrive --medium ~/Downloads/ubuntu-22.04.2-live-server-amd64.iso 

VBoxManage modifyvm $VM_NAME  --boot1 dvd --boot2 disk --boot3 none --boot4 none

Then you can run VM:

VBoxManage startvm $VM_NAME

Based on this guide. 

sign_and_send_pubkey: signing failed for RSA "PIV AUTH pubkey" from agent: agent refused operatio

This error is very annoying and it happens when you use Yubikey for ssh auth and by accident you did not click on Yubikey when you did ssh auth.

After this happens you need to restart machine or ssh agent and all the things to fix it.

When it happens I was able to catch this error log:

sudo systemctl status pcscd.service 

● pcscd.service - PC/SC Smart Card Daemon

     Loaded: loaded (/lib/systemd/system/pcscd.service; indirect; vendor preset: enabled)

     Active: active (running) since Thu 2023-05-04 10:46:27 BST; 2h 39min ago

TriggeredBy: ● pcscd.socket

       Docs: man:pcscd(8)

   Main PID: 2505 (pcscd)

      Tasks: 9 (limit: 38276)

     Memory: 2.6M

        CPU: 88ms

     CGroup: /system.slice/pcscd.service

             └─2505 /usr/sbin/pcscd --foreground --auto-exit

May 04 10:46:27 station systemd[1]: Started PC/SC Smart Card Daemon.

May 04 13:22:18 station pcscd[2505]: 00000000 ccid_usb.c:1566:InterruptStop() libusb_cancel_transfer failed: LIBUSB_ERROR_NO_DEVICE

Then I feed "ccid_usb.c:1566:InterruptStop() libusb_cancel_transfer failed: LIBUSB_ERROR_NO_DEVICE" to Google. 

I have this issue on Ubuntu 22.04 and I've tried version from Ubuntu 22.10 which has version 1.99 of affected package and it did not help. 

Apparently this bugfix may fix this issue and it wasn't part of 1.99 release. Related GitHub issue.

Can Mozilla VPN users connect Mullwad servers directly?

I've tried to fix my IPv6 compatibility issues by using Mozilla VPN over NAT64 box this way.

I've tried to improve this setup but it did not work as expected. 

Mozilla VPN uses Mullwad internally and we can find Mullwad's server name using this interface. Just fill "us-nyc-wg-505" in hostname field and after that you will see something like: "us-nyc-wg-505.relays.mullvad.net".

With this information on our hands we can replace:

Endpoint = x.y.z.y:23662

To:

Endpoint = us-nyc-wg-505.relays.mullvad.net:23662

Sadly in my case this trick did not work ;(

If you have any advice about ways to fix it please share. 

 

Mozilla VPN without UI on Ubuntu Linux 22.04 over NAT64

Mozilla VPN service is a really nice service but their UI does not support IPv6 only environment. I use NAT64 box in my network and it does not help either.

Sadly it's known bug and it's still here ;( Luckily I found nice way to workaround it using command line interface. 

I found nice workaround 

Install their Linux app as documented on web site. 

Then we're going to use console app to authenticate. Start authentication process using:

mozillavpn login

Then check that you're successfully authenticated:

mozillavpn status

Then get list of all available servers:

mozillavpn servers

And select your favourite one:

mozillavpn select us-nyc-wg-505

Generate Wireguard configuration using wgconf option which was added recently:

mozillavpn wgconf > mozilla-vpn.conf

Optiwas added recently. 

Then open mozilla-vpn.conf with editor and alter line like this:

Endpoint = x.y.z.y:23662

To:

Endpoint = 64:ff9b::x.y.z.y:23662

Then establish VPN:

wg-quick up mozilla-vpn.conf

To shutdown it you can use:

wg-quick down mozilla-vpn.conf

In this case we will use NAT64 gateway for connection.

Yubikey ssh on Ubuntu 22.04

Today I did full fresh installation of Ubuntu 22.04 to migrate to new 2T NVME disk from Samsung as I had disk space issues with my old 500G drive. 

After installation I noticed that I cannot use my Yubikey for ssh auth as documented here. 

I tried to add Yubikey as auth source and it failed with pretty weird error:

ssh-add -s /usr/lib/x86_64-linux-gnu/opensc-pkcs11.so

Enter passphrase for PKCS#11: 

Could not add card "/usr/lib/x86_64-linux-gnu/opensc-pkcs11.so": agent refused operation

 This error can mean literally anything.

I've tried running ssh agent manually in foreground mode:

ssh-agent -d

And after that I saw error which sounds like "no available slots".

So I back to guide as I suspected that my Yubikey died and I've sued following command:

sudo ykman list --serials

WARNING: PC/SC not available. Smart card (CCID) protocols will not function.

ERROR: Unable to list devices for connection

1232134323

That's interesting and this error lead me to this bug and I got fix:

 sudo systemctl start pcscd

After that it worked just fine.

As long term fix you need to enable automatic start on machine boot: 

sudo systemctl enable pcscd

Sadly it's known Ubuntu bug. 

Yubikey ssh and signing failed for RSA "PIV AUTH pubkey" from agent: agent refused operation

You may face this issue if you use ssh and Yubikey like covered in this guide. 

Previously I had to reboot machine to address this issue but I found nice trick to get it work.

Originally error looks like:

ssh server

sign_and_send_pubkey: signing failed for RSA "PIV AUTH pubkey" from agent: agent refused operation

root@xxx: Permission denied (publickey).

It may happen when you forgot to tap confirmation on Yubikey and it was just slow.

First attempt to fix it was to kill all ssh agent processes which may be run on system:

ps aux|grep ssh

odintsov   16493  0.0  0.0   7972  5820 ?        S    12:36   0:00 /usr/bin/ssh-agent -D -a /run/user/1000/keyring/.ssh

odintsov   16494  0.0  0.0 164340 11584 ?        SLl  12:36   0:00 /usr/lib/openssh/ssh-pkcs11-helper

odintsov   27798  0.0  0.0   7972  3848 ?        Ss   13:20   0:00 ssh-agent -s

odintsov   27801  0.0  0.0 164340 11572 ?        SLl  13:20   0:00 /usr/lib/openssh/ssh-pkcs11-helper

The best way to kill them is:

pkill ssh

After that we need to start ssh agent again:

eval `ssh-agent -s`

After that load Yubikey key to agent:

ssh-add -s /usr/lib/x86_64-linux-gnu/opensc-pkcs11.so

For last command I use fancy alias in ~/.bashrc:

alias ssh_add='ssh-add -s /usr/lib/x86_64-linux-gnu/opensc-pkcs11.so'

It's not clear why Yubikey fails that way. I think it has something to do with ssh-pkcs11-helper being stuck in operation to Yubikey hardware. 

 

How to enable IPv6 on Google Cloud?

Google Cloud has native support for IPv6 but you need to create special VPC network to use IPv6.

As first step open VPC configuration:

Then create new VPC network and fill all fields as on my screenshot. 

Then configure subnet settings. The most important step to specify dual stack. 

Then you need to create default firewall rules to allow ICMPv6. You may notice that we use number 58 instead of ICMPv6 due to following issue:

Then enable ssh:

After these steps you can create new Compute instances in this region. Then you need to open advanced settings and select our new IPv6 enabled network in list:

And finally select dual stack:

The fun thing that you actually can disable IPv4 completely or you can allocate dedicated IPv6 address for machine. 

Pricing for IPv6 addresses even static ones is mostly free:

Building log4cpp 1.1.4rc3 on msys2 environment on Windows Server 2022

 I got following error during my attempts to build lo4cpp in msys2 environment:

"../include/log4cpp/config-MinGW32.h:27:17: error: 'long long long' is too long for GCC"

It can be easily fixed by commenting following code in file include/log4cpp/config-MinGW32.h

// #define int64_t __int64 

I'll try to report this issue to upstream to have it fixed.  

Got this hint from this blog.

Enabling SSH server on Windows 2022 Datacenter edition

After friend's advice I realised that modern Windows versions have bundled SSH server and that's a best way to work with remote Windows platforms as RDP is not as cool as old good console.

First of all we need to install OpenSSH server component, you can do it this way:

• Start
• Settings
• Apps
• Apps and Features
• Optional Features
• Add Feature
• OpenSSH Server

Then we need to start it. Search for "Services" in search panel and then open it. Looks for OpenSSH SSH server and then click right mouse button and Start it. 

Then open properties and switch startup type from "manual" to "automatic". We need it to launch it automatically on boot.

After that you can connect to this server via normal SSH client from Linux:

Based on this guide.

How to control RGB leds on Logitech G Pro X keyboard from Linux?

 Official software is coming only for Windows but fortunately we have nice project for it.

On Ubuntu or Debian it's very easy to install: 

sudo apt install -y g810-led

Then try setting this thing, it's my favourite one so far:

sudo gpro-led -p /usr/share/doc/g810-led/examples/sample_profiles/colors

Install it as default profile:

sudo cp /usr/share/doc/g810-led/examples/sample_profiles/colors  /etc/g810-led/profile 

Example:

Using Radvd to advertise IPv6 prefix for NAT64

Some time ago I published article about my own NAT64 gateway and configuration for it was quite far away from perfect: 

It even looks ugly as you need to keep this prefix in mind all the time. IPv6 offers very nice way to announce such prefix from our NAT64 box automatically using RA / Router Advertisement announces.

To make it possible we need to install package:

sudo apt-get install -y radvd

Then we need to create configuration for it in file /etc/radvd.conf :

interface end0 {

    MinRtrAdvInterval 3;

    MaxRtrAdvInterval 5;

    

    AdvSendAdvert on;

    AdvDefaultLifetime 0;

    route 64:ff9b::/96 {};

};

With such configuration radvd daemon will advertise that this prefix is accessible via machine's IPv6 address and all hosts in network will be able to use it.  

You will need to replace end0 by name of your external interface of NAT64 box.

Then start it and enable autostart:

sudo systemctl enable radvd

sudo systemctl start radvd

Finally, reboot or disable / enable network on client machine.

To debug it from client I recommend installing this tool:

sudo apt install -y radvdump

Then you need to run application with same name:

radvdump

And after few seconds you will see banner like this:

interface enp37s0f0

{

AdvSendAdvert on;

# Note: {Min,Max}RtrAdvInterval cannot be obtained with radvdump

AdvManagedFlag off;

AdvOtherConfigFlag off;

AdvReachableTime 0;

AdvRetransTimer 0;

AdvCurHopLimit 64;

AdvDefaultLifetime 0;

AdvHomeAgentFlag off;

AdvDefaultPreference medium;

AdvSourceLLAddress on;

route 64:ff9b::/96

{

AdvRoutePreference medium;

AdvRouteLifetime 15;

}; # End of route definition

}; # End of interface definition

In same time your Linux routing table will receive following entry:

sudo ip -6 route|grep ff9

64:ff9b::/96 via fe80::8832:73ff:fe02:edb6 dev enp37s0f0 proto ra metric 100 pref medium

So we have nice network path towards our NAT64 prefix. That's very convenient and works just fine.

As final step I can recommend checking that some IPv4 host is accessible via IPv6 NAT64 prefix.

I've decided to try GitHub:

ping6 64:ff9b::140.82.121.3 -c 3

PING 64:ff9b::140.82.121.3(64:ff9b::8c52:7903) 56 data bytes

64 bytes from 64:ff9b::8c52:7903: icmp_seq=1 ttl=246 time=14.6 ms

64 bytes from 64:ff9b::8c52:7903: icmp_seq=2 ttl=246 time=14.1 ms

64 bytes from 64:ff9b::8c52:7903: icmp_seq=3 ttl=246 time=14.2 ms

--- 64:ff9b::140.82.121.3 ping statistics ---

3 packets transmitted, 3 received, 0% packet loss, time 2003ms

rtt min/avg/max/mdev = 14.145/14.305/14.574/0.190 ms

This approach highlights great deal of flexibility in IPv6 protocol as it was very easy to add new prefix for our own purposes inside of our own network. 

I used following articles as basis for my research one and two. 

In following release after 2.19 radvd will receive update which will make specific statement for NAT64 prefix announcements. 

Realtek 8153 based USB Ethernet adaptor on Debian Linux

I received my Lenovo Ethernet USB 3 adaptor based on Realtek 8153 and it identified well on my PC:

4021.908466] usb 1-1: USB disconnect, device number 6

[ 4021.908858] r8152 1-1:1.0 enx606d3cece3ed: Stop submitting intr, status -108

[ 4023.337656] usb 1-1: new high-speed USB device number 7 using xhci_hcd

[ 4024.434537] usb 1-1: New USB device found, idVendor=17ef, idProduct=720c, bcdDevice=30.00

[ 4024.434542] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6

[ 4024.434543] usb 1-1: Product: Lenovo USB-C to LAN

[ 4024.434545] usb 1-1: Manufacturer: Lenovo

[ 4024.434545] usb 1-1: SerialNumber: ECE3ED000000

[ 4024.599450] usb 1-1: reset high-speed USB device number 7 using xhci_hcd

[ 4025.532652] r8152 1-1:1.0: load rtl8153a-3 v2 02/07/20 successfully

Sadly when I plugged it to my SBC RockPro64 I got following:

[ 4182.236792] usb 7-1: new high-speed USB device number 2 using xhci-hcd

[ 4182.386057] usb 7-1: New USB device found, idVendor=17ef, idProduct=720c, bcdDevice=30.00

[ 4182.386108] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6

[ 4182.386132] usb 7-1: Product: Lenovo USB-C to LAN

[ 4182.386152] usb 7-1: Manufacturer: Lenovo

[ 4182.386171] usb 7-1: SerialNumber: ECE3ED000000

[ 4182.440134] usbcore: registered new interface driver r8152

[ 4182.448147] usbcore: registered new interface driver cdc_ether

[ 4182.610609] usb 7-1: reset high-speed USB device number 2 using xhci-hcd

[ 4182.800168] r8152 7-1:1.0: firmware: failed to load rtl_nic/rtl8153a-3.fw (-2)

[ 4182.800868] firmware_class: See https://wiki.debian.org/Firmware for information about missing firmware

[ 4182.801738] r8152 7-1:1.0: firmware: failed to load rtl_nic/rtl8153a-3.fw (-2)

[ 4182.802385] r8152 7-1:1.0: Direct firmware load for rtl_nic/rtl8153a-3.fw failed with error -2

[ 4182.802401] r8152 7-1:1.0: unable to load firmware patch rtl_nic/rtl8153a-3.fw (-2)

[ 4182.839821] r8152 7-1:1.0 eth0: v1.12.13

[ 4182.880701] r8152 7-1:1.0 enx606d3cece3ed: renamed from eth0

To address it we need to add non-free repository to list of standard Ubuntu repos by adding non-free after main in /etc/apt/sources.list like this:

deb http://deb.debian.org/debian/ debian-code-name main non-free

And then install firmwares:

sudo apt-get update

sudo apt-get install -y firmware-realtek 

After that unplug USB adaptor and plug it again.

In my case I got following successful identification: 

[ 4778.769681] usb 7-1: new high-speed USB device number 4 using xhci-hcd

[ 4809.225536] usb 7-1: new high-speed USB device number 5 using xhci-hcd

[ 4809.374948] usb 7-1: New USB device found, idVendor=17ef, idProduct=720c, bcdDevice=30.00

[ 4809.375000] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6

[ 4809.375024] usb 7-1: Product: Lenovo USB-C to LAN

[ 4809.375044] usb 7-1: Manufacturer: Lenovo

[ 4809.375063] usb 7-1: SerialNumber: ECE3ED000000

[ 4809.570774] usb 7-1: reset high-speed USB device number 5 using xhci-hcd

[ 4809.738340] r8152 7-1:1.0: firmware: direct-loading firmware rtl_nic/rtl8153a-3.fw

[ 4809.760907] r8152 7-1:1.0: load rtl8153a-3 v2 02/07/20 successfully

[ 4809.790911] r8152 7-1:1.0 eth0: v1.12.13

[ 4809.831468] r8152 7-1:1.0 enx606d3cece3ed: renamed from eth0

spotifyd installation Ubuntu Linux 22.04

First of all, we need to install service which can play music from Spotify.

I'll use Spotifyd.

It's relatively easy to build as it uses Rust:

sudo apt install libasound2-dev libssl-dev pkg-config cargo
git clone https://github.com/Spotifyd/spotifyd.git
cd spotifyd

cargo build --release

Then you need to create basic configuration for it which includes login and plain text password. Create configuration folder:

mkdir ~/.config/spotifyd

Then open file with favourite editor:

vim ~/.config/spotifyd/spotifyd.conf

And then add following:

[global]

# Your Spotify account name.

username = "xxx@gmail.com"

# Your Spotify account password.

password = "xxx"

And finally launch daemon:

~/spotifyd/target/release/spotifyd --no-daemon 

Then you can see following log messages when you try to play music:

Loading config from "/home/xxx/.config/spotifyd/spotifyd.conf"

No proxy specified

Using software volume controller.

Connecting to AP "ap.spotify.com:443"

Authenticated as "xxx" !

Using Alsa sink with format: S16

Country: "GB"

Loading <Damascus> with Spotify URI <spotify:track:xxx>

<Damascus> (122880 ms) loaded

For production use I can recommend installing it to /opt:

sudo cp  ~/spotifyd/target/release/spotifyd  /opt/spotifyd

Then you will need to copy configuration file into system configuration path:

sudo cp ~/.config/spotifyd/spotifyd.conf /etc 

And creating systemd unit for it:

sudo vim /lib/systemd/system/spotifyd.service

With following content:

[Unit]

Description=A spotify playing daemon

Documentation=https://github.com/Spotifyd/spotifyd

Wants=sound.target

After=sound.target

Wants=network-online.target

After=network-online.target

[Service]

ExecStart=/opt/spotifyd --no-daemon

Restart=always

RestartSec=12

[Install]

WantedBy=default.target

And finally enable start on boot and start Spotifyd daemon:

sudo systemctl daemon-reload
sudo systemctl enable spotifyd
sudo systemctl start spotifyd

After that I can recommend checking that daemon started successfully using this command:

sudo systemctl status spotifyd

Example output:

spotifyd.service - A spotify playing daemon

     Loaded: loaded (/lib/systemd/system/spotifyd.service; enabled; preset: enabled)

     Active: active (running) since Wed 2023-01-18 14:13:11 GMT; 3s ago

       Docs: https://github.com/Spotifyd/spotifyd

   Main PID: 8963 (spotifyd)

      Tasks: 8 (limit: 4513)

     Memory: 976.0K

        CPU: 30ms

     CGroup: /system.slice/spotifyd.service

             └─8963 /opt/spotifyd --no-daemon

Jan 18 14:13:11 rockpro64 systemd[1]: Started A spotify playing daemon.

Jan 18 14:13:11 rockpro64 spotifyd[8963]: Loading config from "/etc/spotifyd.conf"

Jan 18 14:13:11 rockpro64 spotifyd[8963]: No proxy specified

Jan 18 14:13:11 rockpro64 spotifyd[8963]: Using software volume controller.

Jan 18 14:13:11 rockpro64 spotifyd[8963]: Connecting to AP "ap.spotify.com:443"

Jan 18 14:13:11 rockpro64 spotifyd[8963]: Authenticated as "xxx" !

Jan 18 14:13:11 rockpro64 spotifyd[8963]: Country: "GB"

Jan 18 14:13:11 rockpro64 spotifyd[8963]: Using Alsa sink with format: S16

After that you can install Spotify console client. If you see any errors from client then you will need to click "d" and select spotifyd as output device. 

The great benefits of SpotifyD that it exposes itself via native Spotify protocol and you will see it in your app from phone or another computer:

 

CircleCI hardware: January 2023

I tried to find information about hardware used by CircleCI in Docker and Machine modes but failed to get any up to date information.

I'll focus only on largest resource classes available on Free / OSS plan. 

So I decided to use my own instances to get it. Docker Large.

Internally:

processor : 0

vendor_id : GenuineIntel

cpu family : 6

model : 85

model name : Intel(R) Xeon(R) Platinum 8124M CPU @ 3.00GHz

stepping : 4

microcode : 0x2006c0a

cpu MHz : 2999.998

cache size : 25344 KB

physical id : 0

siblings : 36

core id : 0

cpu cores : 18

apicid : 0

initial apicid : 0

fpu : yes

fpu_exception : yes

cpuid level : 13

wp : yes

flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ss ht syscall nx pdpe1gb rdtscp lm constant_tsc arch_perfmon rep_good nopl xtopology nonstop_tsc cpuid aperfmperf tsc_known_freq pni pclmulqdq monitor ssse3 fma cx16 pcid sse4_1 sse4_2 x2apic movbe popcnt tsc_deadline_timer aes xsave avx f16c rdrand hypervisor lahf_lm abm 3dnowprefetch invpcid_single pti fsgsbase tsc_adjust bmi1 hle avx2 smep bmi2 erms invpcid rtm mpx avx512f avx512dq rdseed adx smap clflushopt clwb avx512cd avx512bw avx512vl xsaveopt xsavec xgetbv1 xsaves ida arat pku ospke

bugs : cpu_meltdown spectre_v1 spectre_v2 spec_store_bypass l1tf mds swapgs taa itlb_multihit mmio_stale_data retbleed

bogomips : 5999.99

clflush size : 64

cache_alignment : 64

address sizes : 46 bits physical, 48 bits virtual

power management:

According to specs this runner allows you to use 4 CPU cores and 8G of memory.

I can clearly see that it can use all 4 CPU cores:

Physical machine is not very overloaded from my perspective but it's clearly busy:

 Let's talk about Machine executor "Linux Large" which is VM.

This one has same number of CPU cores but has more memory:

Considering same cost of Docker Large and Machine Large (20 credits) Machine option looks more attractive.

CPU:

processor : 0

vendor_id : GenuineIntel

cpu family : 6

model : 106

model name : Intel(R) Xeon(R) Platinum 8375C CPU @ 2.90GHz

stepping : 6

microcode : 0xd000331

cpu MHz : 2899.970

cache size : 55296 KB

physical id : 0

siblings : 4

core id : 0

cpu cores : 2

apicid : 0

initial apicid : 0

fpu : yes

fpu_exception : yes

cpuid level : 27

wp : yes

flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ss ht syscall nx pdpe1gb rdtscp lm constant_tsc rep_good nopl xtopology nonstop_tsc cpuid aperfmperf tsc_known_freq pni pclmulqdq ssse3 fma cx16 pcid sse4_1 sse4_2 x2apic movbe popcnt tsc_deadline_timer aes xsave avx f16c rdrand hypervisor lahf_lm abm 3dnowprefetch invpcid_single ssbd ibrs ibpb stibp ibrs_enhanced fsgsbase tsc_adjust bmi1 avx2 smep bmi2 erms invpcid avx512f avx512dq rdseed adx smap avx512ifma clflushopt clwb avx512cd sha_ni avx512bw avx512vl xsaveopt xsavec xgetbv1 xsaves wbnoinvd ida arat avx512vbmi pku ospke avx512_vbmi2 gfni vaes vpclmulqdq avx512_vnni avx512_bitalg tme avx512_vpopcntdq rdpid md_clear flush_l1d arch_capabilities

bugs : spectre_v1 spectre_v2 spec_store_bypass swapgs mmio_stale_data eibrs_pbrsb

bogomips : 5799.94

clflush size : 64

cache_alignment : 64

address sizes : 46 bits physical, 48 bits virtual

power management:

This machine is clearly 100% allocated only for us and I can see how my code uses all available CPU resources:

It's clearly AWS EC2 instance but we can try getting more information about instance type using metadata query:

curl http://169.254.169.254/latest/meta-data/

Let's get instance type:

curl http://169.254.169.254/latest/meta-data/instance-type

m6i.xlarge

And you can find information about it at AWS web site. 

Let's investigate ARM Large VMs.

It's clearly AWS too.

CPU information:

cat /proc/cpuinfo 

processor : 0

BogoMIPS : 243.75

Features : fp asimd evtstrm aes pmull sha1 sha2 crc32 atomics fphp asimdhp cpuid asimdrdm lrcpc dcpop asimddp ssbs

CPU implementer : 0x41

CPU architecture: 8

CPU variant : 0x3

CPU part : 0xd0c

CPU revision : 1

lscpu:

Architecture:                    aarch64

CPU op-mode(s):                  32-bit, 64-bit

Byte Order:                      Little Endian

CPU(s):                          4

On-line CPU(s) list:             0-3

Thread(s) per core:              1

Core(s) per socket:              4

Socket(s):                       1

NUMA node(s):                    1

Vendor ID:                       ARM

Model:                           1

Model name:                      Neoverse-N1

Stepping:                        r3p1

BogoMIPS:                        243.75

L1d cache:                       256 KiB

L1i cache:                       256 KiB

L2 cache:                        4 MiB

L3 cache:                        32 MiB

NUMA node0 CPU(s):               0-3

Vulnerability Itlb multihit:     Not affected

Vulnerability L1tf:              Not affected

Vulnerability Mds:               Not affected

Vulnerability Meltdown:          Not affected

Vulnerability Mmio stale data:   Not affected

Vulnerability Retbleed:          Not affected

Vulnerability Spec store bypass: Mitigation; Speculative Store Bypass disabled via prctl

Vulnerability Spectre v1:        Mitigation; __user pointer sanitization

Vulnerability Spectre v2:        Mitigation; CSV2, BHB

Vulnerability Srbds:             Not affected

Vulnerability Tsx async abort:   Not affected

Flags:                           fp asimd evtstrm aes pmull sha1 sha2 crc32 atomics fphp asimdhp cpuid asimdrdm lrcpc dcpop asimddp ssbs

We can retrieve EC2 instance type using metadata query:

curl http://169.254.169.254/latest/meta-data/instance-type

m6g.xlarge

It's AWS Graviton2 based instance and you can find more details here. 

For full review we can try GCE enabled VM type which can be requested using Android Machine images. 

CPU:

processor : 0

vendor_id : GenuineIntel

cpu family : 6

model : 63

model name : Intel(R) Xeon(R) CPU @ 2.30GHz

stepping : 0

microcode : 0xffffffff

cpu MHz : 2299.998

cache size : 46080 KB

physical id : 0

siblings : 4

core id : 0

cpu cores : 2

apicid : 0

initial apicid : 0

fpu : yes

fpu_exception : yes

cpuid level : 13

wp : yes

flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ss ht syscall nx pdpe1gb rdtscp lm constant_tsc rep_good nopl xtopology nonstop_tsc cpuid tsc_known_freq pni pclmulqdq vmx ssse3 fma cx16 pcid sse4_1 sse4_2 x2apic movbe popcnt aes xsave avx f16c rdrand hypervisor lahf_lm abm invpcid_single pti ssbd ibrs ibpb stibp tpr_shadow flexpriority ept vpid fsgsbase tsc_adjust bmi1 avx2 smep bmi2 erms invpcid xsaveopt arat md_clear arch_capabilities

bugs : cpu_meltdown spectre_v1 spectre_v2 spec_store_bypass l1tf mds swapgs

bogomips : 4599.99

clflush size : 64

cache_alignment : 64

address sizes : 46 bits physical, 48 bits virtual

power management:

Then retrieve instance type using GCE metadata API:

curl "http://metadata.google.internal/computeMetadata/v1/instance/machine-type" -H "Metadata-Flavor: Google"; echo -e "\n"

projects/1027915545528/machineTypes/n1-standard-4

It's n1-standard-4 and you can find official documentation about it here. 

Data as table:

• Machine Linux large: AWS EC2 m6i.xlarge
• Machine Linux large / Android image:  GCE n1-standard-4
• ARM Linux Large: AWS EC2 m6g.xlarge

I'll do performance comparisons between Docker and VMs in future posts. 

 

USB-3 Gigabit 1G Ethernet card

I'm playing with my SBC Rock64Pro and found myself limited by single Ethernet port.

So I decided to find decent Ethernet adapter with USB-3 support.

Fortunately, I found really nice blog which compares performance between Realtek RTL8153 based USB Ethernet adapters and ASIX AX88179 based ones.

Realtek one clearly wins as ASIX shows not very perfect performance and cannot reach 1G in many tests. 

Just for clarity RockPro64 uses RTL8211F based adaptor for onboard ethernet.